Telemecanique XZCPV1164L5

Telemecanique XZCPV1164L5 Pre-Wired Connector: Straight Female M12 5-Pin PVC Cable 5 m

The Telemecanique XZCPV1164L5 pre-wired connector is an industrial cabling accessory engineered to standardize field-device connectivity in automation systems that use M12 circular interfaces. In many plants, installation variability and inconsistent field terminations are major sources of intermittent faults. A molded cordset reduces those risks by delivering a defined connector geometry, consistent pin mapping, and repeatable sealing performance when correctly mated. The Telemecanique XZCPV1164L5 pre-wired connector is specified as a straight female M12 connector with a 5-pin arrangement and a 5 m PVC cable, suited to general-purpose wiring patterns where a multi-conductor interface is required.

Product identity and connector topology

  • Brand + code + type: Telemecanique XZCPV1164L5 pre-wired connector
  • Accessory category: Cabling accessory
  • Connector interface: M12 straight female connector
  • Pin count: 5 pins
  • Cable jacket: PVC
  • Cable length: 5 m
  • Collar material: Metal
  • Connector fixing: Screw-on coupling
  • Status indication: Without status LED
  • Cable composition (class): 5 × 0.25 mm² conductors

These characteristics are documented for XZCPV1164L5.

Why a 5-pin M12 cordset is selected

In M12 ecosystems, a 5-pin layout is commonly used when the field device requires more conductors than a basic 3- or 4-pin sensor—such as additional signaling, multiple channels, or specific interface requirements. The Telemecanique XZCPV1164L5 pre-wired connector provides a 5-pin interface that supports these multi-conductor needs while maintaining compact circular connectivity. For engineering governance, the highest priority is to ensure pin utilization matches the device and the IO endpoint exactly, because mis-mapping in multi-pin systems can cause confusing, intermittent symptoms.

Screw-on coupling and mechanical stability

The Telemecanique XZCPV1164L5 pre-wired connector uses a screw-on coupling and a metal collar, which together support stable mating under vibration and repeated maintenance cycles.
In industrial practice, connector loosening is a frequent root cause of sporadic sensor faults, especially where cables are routed through moving carriers or where equipment is washed down. A screw-on coupling provides a defined mechanical retention method, while the metal collar improves robustness at the mating interface. The outcome is improved connection stability when installed with correct torque and strain relief.

PVC cable: routing discipline and lifecycle control

The PVC jacket of the Telemecanique XZCPV1164L5 pre-wired connector supports general-purpose industrial routing.
Lifecycle performance depends on routing discipline:

  • Maintain bend radius to prevent conductor fatigue near the connector head.
  • Protect against abrasion where the cable passes sharp edges or moving frames.
  • Use strain relief so cable pull does not transmit torque into the M12 coupling.
  • Separate signal cable paths from high-power motor leads where feasible.
  • Document routing so replacements follow the same mechanical path and do not introduce new stress points.

Conductor cross-section and field wiring consistency

The published cable composition (5 × 0.25 mm²) for the Telemecanique XZCPV1164L5 pre-wired connector supports stable signal transmission in typical sensor and device wiring scenarios, while maintaining flexibility for machine routing.
For commissioning, consistent conductor mapping and continuity checks are essential. Because the cordset is pre-wired, the primary variability is not termination quality but the system-side mapping and IO documentation. The correct practice is to verify pin-to-pin continuity, then validate device behavior under operating vibration and temperature.

Deployment patterns and maintenance outcomes

The Telemecanique XZCPV1164L5 pre-wired connector is typically deployed between field devices and decentralized IO blocks, junction boxes, or cabinet bulkhead interfaces that accept M12. The 5 m length enables flexible routing across machine frames while keeping connectivity standardized. In maintenance, pre-wired cordsets reduce mean time to repair because replacement does not require field crimping or re-termination—technicians can swap the assembly and restore a known-good cable path quickly.

For broader ecosystem reference, see Telemecanique sensor.

FAQ

  • Is XZCPV1164L5 a sensor?
    No. The Telemecanique XZCPV1164L5 pre-wired connector is a cabling accessory. {index=15}
  • What connector interface is used?
    It is a straight female M12 connector.
  • How many pins are provided?
    The cordset is specified with 5 pins.
  • What is the cable length and jacket type?
    It is a 5 m cordset with a PVC cable jacket.
  • Does it include a status LED?
    No, it is specified without status LED.